澳洲83期计划

Structural Epoxy Wood Hardener and Consolidant for Deteriorated Wood.

Uses: LiquidWood® penetrates wood fibers and structurally hardens decayed and weathered wood permanently.  Use indoors and outdoors and on both structural and decorative wood. Use to harden and restore wood on buildings, windows, columns, beams, decks, boats, furniture, artwork, and any wooden architectural elements. Use also as a primer or thinner for WoodEpox®.

Features & Benefits: LiquidWood epoxy wood consolidant is easy to use and produces permanent results. Its low viscosity allows it to penetrate deep into the wood and saturate deteriorated wood fibers prior to hardening.  This eliminates the need to remove the areas that can be effectively consolidated. With LiquidWood, deteriorated wood that could crumble under finger pressure can be restored to structural, high-strength, durable, weather and insect-resistant wood.  The absence of water and solvents eliminates shrinkage and enhances adhesion.  It is low odor and produces virtually zero VOCs, making it safe and hazard-free in any environment. Treated wood will harden within hours, and like new wood, can easily be sawed, planed, drilled, nailed, painted, routed, and sanded.

Technical Characteristics: 1:1 mixing ratio. Combine equal parts A and B until fully blended. Pot life: approximately 30 minutes. Hardens within hours depending on temperature and other environmental factors.  100% epoxy solids.  Waterproof. Coverage: 231 cubic inches per gallon.  Effective coverage varies based on the porosity of the wood.  Translucent amber color liquid resin. Apply by brushing, pouring, or injecting directly onto dry, bare wood.  Application temperature range: 50-90° F.  100% compatible with WoodEpox.

Cold weather formulation is available for application temperatures as low as 35° F.

This product is GREENGUARD® Certified, meaning that it has been 3rd party verified to contain virtually no VOC’s (volatile organic compounds).  

(10 customer reviews)
DescriptionUnitQtyPrice
12 Fluid Ounce
$27.75
2 Pint
$55.75
2 Quart
$89.90
2 Gallon
$229.90
10 Gallon
$929.90

澳洲8开奖结果查询

Kg/cm2 Mpa Psi
Compressive Strength 366 36 5210
Elongation 84%
Flexural Strength 63 6.2 900
Hardness, Shore D 42
Tensile Strength 103 10.1 1460

澳洲8冷热号统计

澳洲8开奖结果大小

澳洲8结果

    Can you mail into hardened LiquedWood?
  1. Q Can you mail into hardened LiquedWood? answer now
    Asked by Bill Dull on May 11, 2022 12:01 pm
    Answered by the admin

    Yes.

  2. Can your Liquid Wood /Wood Epox combo be used for laminate countertop pressed board? It is the area where dishwasher screws under counter. Does the product indicate maximum area which can be rebuilt in sq/in (or volume cu/in)?
  3. Q Can your Liquid Wood /Wood Epox combo be used for laminate countertop pressed board? It is the a...... Read more answer now
    Asked by Michael P DiLonardo on May 6, 2022 10:12 am
    Answered by the admin

    LiquidWood is a consolidant for rotted, soft, spongy wood. It is not a protectorant type coating and/or laminating type product. If you apply it to good, solid wood, it will remain on the surface and remain tacky. WoodEpox is used to fill in missing areas in wood.

  4. Does this this product generate heat as it cures? And if so how much. I have a log home and this is an exterior beam. Thank you Gary Winsor
  5. Q Does this this product generate heat as it cures? And if so how much. I have a log home and th...... Read more answer now
    Asked by Gary Winsor on May 3, 2022 12:35 pm
    Answered by the admin

    It may get warm when you mix it, but it's nothing to be alarmed about.

  6. Does liquid wood bind metal? Want to insert an iron bar into punky wood
  7. Q Does liquid wood bind metal? Want to insert an iron bar into punky wood answer now
    Asked by david argilla on May 2, 2022 11:33 am
    Answered by the admin

    LiquidWood will consolidate that punky wood and should bond to both wood and the iron bar.

  8. How do you order? I have been ordering online for over 25 year.
  9. Q How do you order? I have been ordering online for over 25 year. answer now
    Asked by Bryan Paris on April 27, 2022 4:45 pm
    Answered by the admin

    You can order on our website or by calling us at 800-445-1754.

Send me a notification for each new answer.

澳洲8开奖结果网址

  1. ABATRON

    Thanks for the feedback. We do suggest a longer induction period in order to avoid the tacky-blushing. 5-10 minutes is recommended. Humidity and moisture in the wood can affect the tackiness as well. Using an external heat source can speed up the cure significantly as well.

  2. William H

    The product does what says, but takes a L-O-N-G time fully cure. Both times that I have used it, after 12 hours at ambient temperature (60-80 deg F) the surface is still very tacky. Now, I will say that after I mixed it well a good full minute, I let it sit for the mix to go from foamy to de-air and become clear. Maybe waiting longer would reduce the tackiness, but it took me about 15 minutes to fully apply with a coarse haired brush, so I was confident that the length of time and the constant applying should have given me the required time to not experience tackiness.

    Product does what is says as far as binding wood and protecting it. But, if it that time sensitive regarding tackiness, I may look elsewhere for the next time.

  3. ABATRON

    You can thin LiquidWood with Abosolv, Acetone, Xylene or Alcohol.

  4. Er

    I have used it on an old log homes very satisfied with this product I was wondering how to make it thinner so it would penetrate the entire surface and get into the small cracks

  5. Cheri

    I’ve used Abatron products in many areas as we’ve slowly restored our circa 1900 home. It’s easy to use, works perfectly, and has saved us a lot of money and hard work because we’ve restored the original wood parts – rather than replacing them.

  6. Donald Chester

    I have used LiquidWood for years in restoration projects in and around my circa 1865 farmhouse and circa 1930 outbuilding. I prefer to make my own filler by mixing LiquidWood with fine sawdust, since after sanding, the colour comes out close to that of the surrounding wood even before finishing; sometimes it is hard to see where the repair was made, for example, where I repaired a burnt spot in my oak hardwood floor from an errant ember from the wood stove. I have used this method outdoors to repair rotted window sills and siding. It doesn’t shrink and after more than a decade, no cracks have appeared between filler and sound wood. Filled spots take paint just like original wood.

  7. ABATRON

    It’s hard to say how much LiquidWood will absorb into the rotted wood because we don’t know the extent of the rot. You should keep brushing it on and/or injecting it until the product pools on the top, then you know you’ve applied enough product.

  8. Ed

    what is the ration of liquid wood to the beam one would be working with?

  9. ABATRON

    Yes, you can drill holes and inject the LiquidWood.

  10. Chiya

    I have soft spots in my floorboards throughout my custom renovated home. The top layer of teak flooring is in great shape. Can I somehow inject the liquid hardener into the soft spots to fix the rotted boards below?

  11. Anthony Smiley

    I use the Wood sealer 1st . Then I used the wood filler. Both products were easy to work with. I was repairing a rotted 2 by 12 joist. The wood sealer made the would extremely hard again. I then use the would filler to fill in the large Spaces. The A and B wood filler was like playing with clay . Very easy to use. I will give it a five star after I sand and shape the wood. Ps I have pictures if you would like to see them. Let me know.

  12. Laurel

    none better!

  13. eugene weddle

    good

  14. James Listman

    This stuff is a mandatory for anyone with an older home trying to maintain old sills etc. Making sure the old wood is dry is critical. It sucks right in and truly does make the original better!

Add a review

Your email address will not be published.

澳洲8免费计划